Se necesita TSQL Hack para obtener un filtro de datos
Pregunta
Una interfaz de usuario (antes de que se muestre el informe) muestra una búsqueda (Combo) que tiene
- (ID = 0). Todas las unidades organizativas
- (ID =4).HR
- (ID = 5).DEV
Necesito:
- Se puede mostrar datos de (4) + (5) si (0) se seleccionan.
- Solo (4) O (5) si se selecciona HR o DEV.
Código combinado de búsqueda (Seleccionado alimenta el parámetro en la siguiente consulta).
Select 0 AS ID,'All Org' AS Name from DP_ORG_OrganizationUnit
where DP_ORG_OrganizationUnit.Code IN {AccessData}
Union
SELECT
DP_ORG_OrganizationUnit.ID,
DP_ORG_OrganizationUnit.Name
FROM DP_ORG_OrganizationUnit where DP_ORG_OrganizationUnit.Code IN ('HR','DEV')
Consulta de fila de datos del informe
SET CONCAT_NULL_YIELDS_NULL OFF
DECLARE @EmpID as int;
DECLARE @OrganizationUnit as int;
DECLARE @StartDate as datetime;
DECLARE @EndDate as datetime;
SET @EmpID = ?;
SET @StartDate = ?;
SET @EndDate = ?;
SET @OrganizationUnit = ?;
SELECT
Employee.Code,
Employee.Name1+' '+Employee.Name2+' '+Employee.Name3+' '+Employee.Name4+' '+Employee.Name5 AS FullName,
Employee.OrganizationUnit,
ContractType.Name,
EmployeeContract.StartDate,
EmployeeContract.EndDate
FROM Employee INNER JOIN (ContractType INNER JOIN EmployeeContract
ON ContractType.ID = EmployeeContract.ContractType)
ON Employee.ID = EmployeeContract.Employee
WHERE (Employee.ID = @EmpID OR @EmpID=0)
AND
(Employee.OrganizationUnit = @OrganizationUnit OR @OrganizationUnit=0)
AND NOT((EndDate < @StartDate or StartDate > @EndDate));
¿Alguna forma de lograrlo por su apariencia?0=0 mostraría todos los datos de otros departamentos también ..
¿Alguien :-o?
Solución
En primer lugar, su código de búsqueda combinado podría ser apretado un poco:
-- the FROM clause was superfluous
SELECT 0 AS ID,'All Org' AS Name
UNION ALL
-- the two-part identifiers were superfluous (only one table)
SELECT ID, Name
FROM DP_ORG_OrganizationUnit
WHERE Code IN ('HR','DEV')
Para la consulta del informe, la forma más simple sería:
WHERE
((@OrganizationUnit > 0 AND Employee.OrganizationUnit = @OrganizationUnit) OR
(@OrganizationUnit = 0 AND Employee.OrganizationUnit IN (4,5)))
Otros consejos
algo como esto debería funcionar
Where (Employee.OrganizationUnit = case when @OrganizationUnit=0 then 4 else @OrganizationUnit end OR case when @OrganizationUnit=0 then 5 else @OrganizationUnit end)
Prueba de esto, que debería utilizar índices en su consulta ...
DECALRE @FilterValues (FilterValue int not null primary key)
IF @Param=0
BEGIN
INSERT INTO @FilterValues VALUES (4)
INSERT INTO @FilterValues VALUES (5)
END
ELSE ID @PAram IS NOT NULL
BEGIN
INSERT INTO @FilterValues VALUES (@Param)
END
SELECT
....
FROM YourTable y
INNER JOIN @FilterValues f ON y.Value=f.Value
WHERE .....
versión de KM va a funcionar, pero esta consulta no necesita una tabla temporal ...
SELECT *
FROM Employee
WHERE (
@OrganizationUnit = 0
OR
(
@OrganizationUnit <> 0
AND
Employee.OrganizationUnit = @OrganizationUnit
)
)
¿Qué tal
WHERE (Employee.ID = @EmpID OR @EmpID=0)
AND
(Employee.OrganizationUnit BETWEEN ISNULL(NULLIF(@OrganizationUnit,0),0) AND ISNULL(NULLIF(@OrganizationUnit,0),99))
AND NOT((EndDate < @StartDate or StartDate > @EndDate));
Licenciado bajo: CC-BY-SA con atribución
No afiliado a StackOverflow