Set DCB Fails When Attempting to Configure COM Port

Question

I'm trying to write a C++ MFC application that uses the serial port (e.g. COM8). Every time I try to set the DCB it fails. If someone can point out what I'm doing wrong, I'd really appreciate it.

DCB dcb = {0};

dcb.DCBlength = sizeof(DCB);
port.Insert( 0, L"\\\\.\\" );

m_hComm = CreateFile(
    port,                           // Virtual COM port
    GENERIC_READ | GENERIC_WRITE,   // Access: Read and write
    0,                              // Share: No sharing
    NULL,                           // Security: None
    OPEN_EXISTING,                  // The COM port already exists.
    FILE_FLAG_OVERLAPPED,           // Asynchronous I/O.
    NULL                            // No template file for COM port.
    );

if ( m_hComm == INVALID_HANDLE_VALUE )
{
    TRACE(_T("Unable to open COM port."));
    ThrowException();
}

if ( !::GetCommState( m_hComm, &dcb ) )
{
    TRACE(_T("CSerialPort : Failed to get the comm state - Error: %d"), GetLastError());
    ThrowException();
}

dcb.BaudRate = 38400;               // Setup the baud rate.
dcb.Parity = NOPARITY;              // Setup the parity.
dcb.ByteSize = 8;                   // Setup the data bits.
dcb.StopBits = 1;                   // Setup the stop bits.

if ( !::SetCommState( m_hComm, &dcb ) ) // <- Fails here.
{
    TRACE(_T("CSerialPort : Failed to set the comm state - Error: %d"), GetLastError());
    ThrowException();
}

Thanks.

Additional Info: The generated error code is 87: "The parameter is incorrect." Probably Microsoft's most useful error-code. j/k

Answer 1

I was able to resolve the problem using BuildCommDCB:

DCB dcb = {0};

if ( !::BuildCommDCB( _T("baud=38400 parity=N data=8 stop=1"), &dcb ) )
{
    TRACE(_T("CSerialPort : Failed to build the DCB structure - Error: %d"), GetLastError());
    ThrowException();
}

Answer 2

My money is on this:

dcb.StopBits = 1; 

The MSDN docs says this about StopBits:

The number of stop bits to be used. This member can be one of the following values.

ONESTOPBIT    0    1 stop bit.
ONE5STOPBITS  1    1.5 stop bits.
TWOSTOPBITS   2    2 stop bits.

So, you're asking for 1.5 stop bits, which is such a horribly archaic thing I can't even remember where it comes from. Teleprinters, possibly.

I'd guess the chances of your driver/hardware supporting this mode are slim, hence the error.

So, change it to dcb.StopBits = ONESTOPBIT;

Answer 3

Here are some possibilities in no particular order.

• GetCommState is filling the structure with garbage since the port hasn't been initialized yet. You might just skip this step.
• There are two parameters that control the Parity settings, and it's not clear if there's any invalid combinations.
• The value for StopBits is not the number of bits, it's a magic number constant. The value 1 equates to ONE5STOPBITS which might be invalid when combined with the other parameters.

Answer 4

This is my code and its working well.

/* Try to open the port */
hCom = CreateFile(szPort, GENERIC_READ | GENERIC_WRITE, 0, 0, OPEN_EXISTING, 0, 0);

if (hCom != INVALID_HANDLE_VALUE) {
    printf("Handle success\n");
}

    dcb = { 0 };
    dcb.DCBlength = sizeof(dcb);

    fSuccess = GetCommState(hCom, &dcb);

    if (!fSuccess) {
        // Handle the error.
        printf("GetCommState failed with error %d.\n", GetLastError());
        CloseHandle(hCom);
        return APP_ERROR;
    }

    // Fill in DCB: 57,600 bps, 8 data bits, no parity, and 1 stop bit.
    dcb = { 0 };
    dcb.DCBlength = sizeof(dcb);

    dcb.BaudRate = CBR_115200;     // Set the baud rate
    dcb.ByteSize = 8;              // Data size, xmit, and rcv
    dcb.Parity = NOPARITY;         // No parity bit
    dcb.StopBits = ONESTOPBIT;     // One stop bit

    fSuccess = SetCommState(hCom, &dcb);

    if (!fSuccess) {
        // Handle the error.
        printf("SetCommState failed with error %d.\n", GetLastError());
        CloseHandle(hCom);
        return APP_ERROR;
    }
}

printf("Serial port successfully reconfigured.\n");

Answer 5

Look at the parameters you give to the function. They're probably incorrect, as the error code says. A google search for "SetCommState 87" shows several instances where the parameters (e.g. baud rate) weren't compatible with the serial port.