Discovering linux disk configurations from the command line
https://stackoverflow.com/questions/586180
-
06-09-2019 - |
italiano
english
français
española
中国
日本の
العربية
Deutsch
한국어
Português
RussianQuestion
How can I discover if a remote machine is configured with or without hardware or software RAID? All I know is i have 256GB at present, I need to order more space but before I can I need to know how the drives are configured.
df lists the drive as:
/dev/sdb1 287826944 273086548 119644 100% /mnt/db
and hdparm:
/dev/sdb: HDIO_GET_MULTCOUNT failed: Invalid argument readonly = 0 (off) readahead = 256 (on) geometry = 36404/255/63, sectors = 299439751168, start = 0
What else should I run and what should I look for?
Solution
Software RAID would not be /dev/sdb - dev/md0. Nor is it LVM.
So it's either real hardware RAID, or a raw disk.
lspci might show you and RAID controllers plugged in.
dmesg | grep sdb might tell you some more about the disk.
sdparm /dev/sdb might tell you something? Particularly if it really is a SCSI disk.
OTHER TIPS
To check for software RAID:
cat /proc/mdstat
On my box, this shows:
Personalities : [raid1]
md0 : active raid1 sda1[0] sdb1[1]
96256 blocks [2/2] [UU]
md1 : active raid1 sda2[0] sdb2[1]
488287552 blocks [2/2] [UU]
unused devices: <none>
You get the names of all software RAID arrays, the RAID level for each, the partitions that are part of each RAID array, and the status of the arrays.
dmesg might help.
On a system where we do have software raid we see things like:
SCSI device sda: 143374744 512-byte hdwr sectors (73408 MB)
sda: Write Protect is off
sda: Mode Sense: ab 00 10 08
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sda: 143374744 512-byte hdwr sectors (73408 MB)
sda: Write Protect is off
sda: Mode Sense: ab 00 10 08
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB)
sdb: Write Protect is off
sdb: Mode Sense: ab 00 10 08
SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB)
sdb: Write Protect is off
sdb: Mode Sense: ab 00 10 08
SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1 sdb2
sd 0:0:1:0: Attached scsi disk sdb
A bit later we see:
md: md0 stopped.
md: bind
md: bind
md: raid0 personality registered for level 0
md0: setting max_sectors to 512, segment boundary to 131071
raid0: looking at sda2
raid0: comparing sda2(63296000) with sda2(63296000)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb2
raid0: comparing sdb2(63296000) with sda2(63296000)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 126592000 blocks.
raid0 : conf->hash_spacing is 126592000 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
and a df shows:
Filesystem Size Used Avail Use% Mounted on /dev/sda1 7.8G 3.3G 4.2G 45% /
tmpfs 2.0G 0 2.0G 0% /dev/shm
/dev/md0 117G 77G 35G 69% /scratch
So part of sda and all of sdb have been bound as one raid volume.
What you have could be one disk, or it could be hardware raid. dmesg should give you some clues.
It is always possible that it is a hardware raid controller that just looks like a single sata (or scsi) drive. Ie, our systems with fiber channel raid arrays, linux only sees a single device, and you control the raid portion and disk assignment via connecting to the fiber raid array directly.
You can try mount -v or you can look in /sys/ or /dev/ for hints. dmesg might reveal information about the drivers used, and lspci could list any add-in hw raid cards, but in general there is no generic method you can rely on to find out the exact hardware & driver setup.
