•  29-05-2021
  •  | 
  •  

Question

I'm trying to send out an email from my as400 unsuccessfully! I'm using this code into a CLLE:

SNDDST     TYPE(*LMSG) TOINTNET((*NONE) +
       ('address1@mail.it') +           
       ('address2@mail.it')) DSTD('TEST') +
LONGMSG('test mail...')

I received an error for my user that I fixed with WRKDIRE where I added the user, in fact now when I call the program, read into dspjoblog: The sending of the distribution was completed successfully. But I do not receive anything in mailboxes

I think that SMTP configuration is OK but I receive this error:

      Tipo    Tipo   ----Registrata----               -----Mittente-----  Num. 
Opz Funzione  voce   Data       Ora      Nome lav.    ID utente  Indir.   seq  
     *RTR    *ERR   10/04/12  13:04:15  QMSF         MARCO     MT        0013 


Funzione . . . . . . . . . . :   Instradamento distribuzione  
Lavoro . . . . . . . . . . . :   275842/QMSF/QMSF             
Data/ora . . . . . . . . . . :   10/04/12  13:04:15           

Mittente:                                                     
ID utente/Indirizzo  . . . :   MARCO     MT                 
Nome sistema/Gruppo. . . . :   S6518B7A                     
Numero di sequenza . . . . . :   0013                         
Data/ora di origine  . . . . :   10/04/12  13:04:15           
Agente destinazione  . . . . :   OfficeVision                 

Codice stato SNADS . . . . . :   0001 Errore instradamento    
Destinatario in errore:                                       
ID utente/Indirizzo  . . . :   INTERNET  GATEWAY            
Nome sistema/Gruppo  . . . :   INTERNET                     
Voce indirizzario sistema  :   Definito localmente

I've found this error:

Message. . . : Failed opening file IFS (Integrated File System)
on file/MMAIL/temp/Q6.txt
Cause. . . . . : The RTCP function requires the use of a file IFS (Integrated
   File System) / MMAIL/temp/Q6.txt. The error received by the call is 3025.
   This file does not exist in the system is blocked or damaged and can not
    be used at the time.
Correction. . . : Close MSF (Mail System Framework) "ENDMSF" and restart
 "STRMSF".

I've just tried to restart job without success and always in QMSF job this error log:

Message ID. . . . . : Severity CPFAF98. . . . . . . : 60
Message type. . . . : Informational
Submit Date. . . . . . : 13/04/12 Time sent. . . . . . : 12:44:02

Message. . . : The job has stopped processing 320083/QMSF/QMSF
  MSF message.
Cause. . . . . : The program exit point in the library QTMSFWD QTCP
  to the point of exit QIBM_QZMFMSF_MSG_FWD has detected a condition with
  6518B7A0909081414210000000008 the message ID. The message indicates that
  processing must be completed. The MSF message will be revised
  the next command execution STRMSF (Start Mail Server Framework)
Correction. . . : Determine because the program exit point has
  indicated the need to end processing of a message. in
  joblog may be listed messages that have caused
  incorrect program. Correct errors, and run the
ENDMSF command (closing mail server framework) to terminate
Was it helpful?

Solution

You could start by looking at SNADS logs using DSPDSTLOG.

IBM support document "SNADS - Basic Troubleshooting Process" is very helpful in finding the source of error. Hope this helps...

http://www-01.ibm.com/support/docview.wss?uid=nas1b56c1c34b489e7528625663d004b1797

OTHER TIPS

There are many things to check. Since you haven't described the things you did do, it is difficult to suggest other things you could do. May I suggest some reading material?

Try using @Buck Calabro's links and here are a couple others. SMTP may not be fully setup right.

Licensed under: CC-BY-SA with attribution
Not affiliated with StackOverflow
scroll top