I am designing a shift register using hierarchical structural Verilog. I have designed a D flip flop and an 8 to 1 mux that uses 3 select inputs. I am trying to put them together to get the full shift register, but my output only gives "XXXX" regardless of the select inputs.
Flip Flop Code
module D_Flip_Flop(
input D,
input clk,
output Q, Q_bar
);
wire a,b,c,d;
nand(a,D,b);
nand(b,a,clk,d);
nand(c,a,d);
nand(d,c,clk);
nand(Q,d,Q_bar);
nand(Q_bar,b,Q);
endmodule
8 to 1 Mux
module Mux8to1(
input [2:0]S,
input A,B,C,D,E,F,G,H,
output Out
);
wire a,b,c,d,e,f,g,h;
and(a, A,~S[2],~S[1],~S[0]);
and(b, B,~S[2],~S[1],S[0]);
and(c, C,~S[2],S[1],~S[0]);
and(d, D,~S[2],S[1],S[0]);
and(e, E,S[2],~S[1],~S[0]);
and(f, F,S[2],~S[1],S[0]);
and(g, G,S[2],S[1],~S[0]);
and(h, H,S[2],S[1],S[0]);
or(Out, a,b,c,d,e,f,g,h);
endmodule
Hierarchical Combination of the Two
module shiftRegister_struct(
input clk,
input [2:0]S,
input [3:0]L,
output reg [3:0]V
);
wire a,b,c,d;
wire V_bar[3:0];
Mux8to1 stage3(S[2:0],V[3],V[0],V[2],1'b0,V[2],V[3],V[2],L[3],a);
Mux8to1 stage2(S[2:0],V[2],V[3],V[1],V[3],V[1],V[3],V[1],L[2],b);
Mux8to1 stage1(S[2:0],V[1],V[2],V[0],V[2],V[1],V[2],V[1],L[1],c);
Mux8to1 stage0(S[2:0],V[0],V[1],V[3],V[1],1'b0,V[1],1'b0,L[0],d);
D_Flip_Flop stage3b(a,clk,V[3],V_bar[3]);
D_Flip_Flop stage2b(b,clk,V[2],V_bar[2]);
D_Flip_Flop stage1b(c,clk,V[1],V_bar[1]);
D_Flip_Flop stage0b(d,clk,V[0],V_bar[0]);
end module
Any thoughts on what might be screwing up my output? The output is V[3:0]
.
I should also include my test bench code:
module Shift_Test_Bench;
// Inputs
reg [2:0] S;
reg [3:0] L;
reg clk;
integer i;
integer j;
// Outputs
wire [3:0] V;
// Instantiate the Unit Under Test (UUT)
shiftRegister_struct uut (
.clk(clk),
.S(S),
.L(L),
.V(V)
);
initial begin
// Initialize Inputs
S = 7;
L = 3;
clk = 1;
// Wait 100 ns for global reset to finish
#100;
// Add stimulus here
for(i = 0; i < 16; i = i+1)
begin
S = i;
for(j = 0; j < 2; j = j+1)
begin
clk = !clk;
#5;
end
end
end
endmodule